 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Jumbo-LED 15.11.2007 Radiation Infrared 5,08 ELJ-870-649 rev. 04 Case Plastic lens, metal case Type 4W Technology AlGaAs/GaAlAs Description High-power infrared LED in an aluminium case with thread socket, for easy handling and heat sink mounting 1,5 O12,5 O16 O11 O1,7 1 2 Outline: H = 12.4 mm ( 0.5) 2 4,5 Applications Medical appliances, remote control and optical communications, light barriers, measurement systems 7,9 D = 16 mm ( 0.5) Thread M10 1 2 8 Pin 1 - cathode Pin 2 - anode 13 M10 Absolute Maximum Ratings at Tamb = 25C, on heat sink (S 200 cm), unless otherwise specified Parameter DC forward current Peak forward current Power dissipation Operating temperature range Storage temperature range Junction temperature Test onditions on heat sink tp10 s, f500 Hz on heat sink on heat sink on heat sink on heat sink Symbol IF IFM P Tamb Tstg Tj Value 1.5 2,0 4 -25 to +100 -25 to +100 100 Unit A A W C C C Electrical Characteristics Tamb = 25C, unless otherwise specified Test Parameter conditions Forward voltage Forward voltage* Switching time Reverse voltage IF = 350 mA IF = 1000 mA IF = 350 mA IR = 10 A Symbol VF VF tr, tf VR RthJC 5 10 K/W Min Typ 1.6 2.0 10/22 Max 1.9 2.3 Unit V V ns Thermal resistance junction-case *only recommended on optimal heat sink We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Kopenicker Str.325 b, Haus 201 1 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED 15.11.2007 ELJ-870-649 rev. 04 Optical Characteristics at Tamb = 25C, on heat sink (S 200 cm), unless otherwise specified Test Parameter Symbol Min conditions Radiant power Radiant power* Radiant intensity Radiant intensity* Peak wavelength Spectral bandwidth at 50% Viewing angle IF = 350 mA IF = 1000 mA IF = 350 mA IF = 1000 mA IF = 350 mA IF = 350 mA IF = 350 mA e e e e p 0.5 860 70 Typ 90 240 210 615 870 42 35 880 Max Unit mW mW mW/sr mW/sr nm nm deg *only recommended on optimal heat sink Note: All measurements carried out withEPIGAP equipment, on blank aluminium heat sink, S = 180 cm, passive cooling. Measurement results and curve characteristics obtained with other heat sinks may differ. 20 Typical wavelength shift vs. forward current (rel. to P @ IF = 350 mA) 15 Wavelength shift (nm) 10 5 0 -5 0 500 1000 1500 IF (mA) We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Kopenicker Str.325 b, Haus 201 2 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED 15.11.2007 ELJ-870-649 rev. 04 4 Radiant power vs. forward current (typical) normalized to E @ IF= 350 mA 3 e (rel.) 2 1 0 0 500 1000 1500 IF (mA) 4 Forward voltage vs. forward current (typical) 3 UF (V) 2 1 0 0 500 1000 1500 IF (mA) We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Kopenicker Str.325 b, Haus 201 3 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED 15.11.2007 ELJ-870-649 rev. 04 Ambient Temperature vs. maximal forward current 2.0 Max. forward current (A) 1.5 1.0 0.5 0.0 0 25 50 75 100 Ambient Temperature (C) Remarks concerning optical radiation safety* At low forward current (<250 mA), and continuous operation, this LED may be classified as LED product Class 1 , according to standard IEC 60825-1:A2. Class 1 products are safe to eyes and skin under reasonably predictable conditions. This implicates a direct observation of the light beam by means of optical instruments. When driven with higher continuous forward current, (up to max. DC current), this product should be classified as LED product Class 1M , according to standard IEC 60825-1:A2. Class 1M products are safe to eyes and skin under normal conditions, including when users view the light beam directly. Class 1M products produce either a highly divergent beam or a large diameter beam. Therefore only a small part of the whole light beam can enter the eye. However, such optical products can be harmful to the retina if the beam is viewed using magnifying optical instruments. Therefore, users should not incorporate optics that could concentrate the output into the eyes. *Note: Safety classification of an optical component mainly depends on the intended application and the way the component is being used. Furthermore, all statements made to classification are based on calculations and are only valid for this LED "as it is", and at continuous operation. Using pulsed current or altering the light beam with additional optics may lead to different safety classifications. Therefore these remarks should be taken as recommendation and guideline only. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Kopenicker Str.325 b, Haus 201 4 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 Jumbo-LED 15.11.2007 ELJ-870-649 rev. 04 Handling precautions To prevent damage to the LED during soldering and assembly, following precautions have to be taken into account. a) The bending point of the lead frame should be located at least 2.5 mm away from the body. b) While bending, the base of the lead frame has to be fixed with radio pliers or similar. c) To ensure an adequate strain relief, the lead frames have to be firmly fixed during soldering. d) Avoid any torsion or tensile loading of the lead frames, especially when they have been heated after being soldered. e) LEDs are static sensitive devices, so adequate handling precautions have to be taken, e.g. wearing grounding wrist straps. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications.All operating parameters must be validated for each customer application by the customer. EPIGAP Optoelektronik GmbH, D-12555 Berlin, Kopenicker Str.325 b, Haus 201 5 of 5 Tel.: +49-30-6576 2543, Fax : +49-30-6576 2545 |
Price & Availability of ELJ-870-649
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |